View HLMP-CW46-QRB00_62371.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Agilent T-1 3/4 (5mm) Extra Bright Precision Optical Performance White LED Lamps.
Data Sheet
Features * Well defined spatial radiation pattern
HLMP-CW46, HLMP-CW47. HLMP-CW76, HLMP-CW77
* High luminous white emission * Viewing angle: 50 and 70. * Standoff or non-standoff leads * Superior resistance to moisture
Description These high intensity white LED lamps are based on InGaN material technology. A blue LED die is coated by phosphor to produce white. The typical resulting color is described by the coordinates x = 0.31, y = 0.31 using the 1931 CIE Chromaticity Diagram. These T-1 3/4 lamps are untinted, diffused, and incorporate precise optics which produce well-defined spatial radiation patterns at specific viewing cone angle.
Applications * Electronic signs and signals * Small area illumination * Legend backlighting * General purpose indicators Benefit * Reduced power consumption, higher reliability, and increased optical/mechanical design flexibility compared to incandescent bulbs and other alternative white light sources.
Caution: Devices are Class 1 ESD sensitive. Please observe appropriate precautions during handling and processing. Refer to Application Note AN-1142 for additional details.
Package Dimensions
5.00 0.20 (0.197 0.008) 8.71 0.20 (0.343 0.008) 1.14 0.20 (0.045 0.008)
5.00 0.20 (0.197 0.008) 8.71 0.20 (0.343 0.008) DIMENSION H
2.35 (0.093) MAX. 0.70 (0.028) MAX. 31.60 MIN. (1.244)
1.14 0.20 (0.045 0.008) 1.50 0.15 (0.059 0.006) 0.70 (0.028) MAX.
31.60 MIN. (1.244)
CATHODE LEAD
CATHODE LEAD
DIMENSION H: 50: 11.98 0.25mm (0.4715 0.01 inches) 70: 11.09 0.25mm (0.4365 0.01 inches)
1.00 MIN. (0.039)
0.50 0.10 SQ. TYP. (0.020 0.004)
1.00 MIN. (0.039)
0.50 0.10 SQ. TYP. (0.020 0.004)
5.80 0.20 (0.228 0.008) CATHODE FLAT 2.54 0.38 (0.100 0.015)
5.80 0.20 (0.228 0.008) CATHODE FLAT 2.54 0.38 (0.100 0.015)
Package Dimension A
Package Dimension B
Notes: 1. All dimensions are in millimeters /inches. 2. Epoxy meniscus may extend about 1mm (0.040") down the leads. 3. If heat-sinking application is required, the terminal for heat sink is anode.
Part Numbering System
H L M P - CW XX - X X X XX Mechanical Option 00: Bulk DD: Ammo Pack Straight Leads Color Bin Options 0: Full color bin distribution B: Color bin 2 & 3 only Maximum Intensity Bin 0: No maximum intensity bin limit Others: Refer to Device Selection Guide Minimum Intensity Bin Refer to Device Selection Guide Viewing Angle and Standoff Option 46: 50 without standoff 47: 50 with standoff 76: 70 without standoff 77: 70 with standoff
2
Device Selection Guide
Typical Viewing Angle, 2 1/2 (Degree) 50 50 50 50 50 50 70 70 70 70 70 70 Intensity (mcd) at 20 MA Min. 880 1150 1150 880 1150 1150 680 880 880 680 880 880 Max. 2500 1900 1900 2500 1900 1900 1900 1500 1500 1900 1500 1500 Standoff No No No Yes Yes Yes No No No Yes Yes Yes Package Dimension A A A B B B A A A B B B
Part Number HLMP-CW46-PS0xx HLMP-CW46-QR0xx HLMP-CW46-QRBxx HLMP-CW47-PS0xx HLMP-CW47-QR0xx HLMP-CW47-QRBxx HLMP-CW76-NR0xx HLMP-CW76-PQ0xx HLMP-CW76-PQBxx HLMP-CW77-NR0xx HLMP-CW77-PQ0xx HLMP-CW77-PQBxx
Notes: 1. Tolerance for luminous intensity measurement is +/- 15% 2. The luminous intensity is measured on the mechanical axis of the lamp package. 3. The optical axis is closely aligned with the package mechanical axis. 4. 21/2 is the off-axis angle where the luminous intensity is 1/2 the on axis intensity
Absolute Maximum Rating at TA = 25oC
Parameters DC forward current
[1] [2]
Value 30 100 30 105 110 -40 to +85 -40 to +100
[3]
Unit mA mA mA mW
o o o o
Peak pulsed forward current Average forward current Power dissipation LED junction temperature Operating temperature range Storage temperature range Wave soldering temperature
C C C C
250 for 3 seconds
Notes: 1. Derate linearly as shown in figure 2. 2. Duty factor 10%, frequency 1KHz 3. 1.59 mm (0.060 inch) below body
3
Electrical/Optical Characteristics TA = 25oC
Parameters Forward voltage Reverse Voltage
[1]
Symbol VF VR RJ-PIN
[2]
Min 5.0
Typ 3.2 240 0.31 0.31 70
Max 4.0
Units V V
o
Test Condition IF = 20 mA IR = 10 A LED Junction to anode lead IF = 20 mA VF=0, f=1MHz
Thermal resistance Chromaticity Coordinates Capacitance
C/W
X Y C
Notes: 1. The reverse voltage of the product is equivalent to the forward voltage of the protective chip at IR = 10 A 2. The chromaticity coordinates are derived from the CIE 1931 Chromaticity Diagram and represent the perceived color of the device.
1.0
35 IF - FORWARD CURRENT - mA 30
RJ-A = 585C/W
1.5
RELATIVE LUMINOUS INTENSITY
RELATIVE LUMINOUS INTENSITY
0.8 0.6 0.4 0.2 0.0 380
1.2 0.9 0.6 0.3 0 0 10 20 30 FORWARD CURRENT - mA
25
RJ-A = 780C/W
20 15 10 5 0 0 20 40 60 80 100 AMBIENT TEMPERATURE - C
480 580 680 WAVELENGTH - nm
780
Figure 1. Relative Intensity vs. Wavelength
Figure 2. Forward Current vs. Ambient Temperature
Figure 3. Relative Intensity versus DC Forward Current
0.025 0.020
IF - FORWARD CURRENT - mA
30
1mA 5mA 10mA
25 20 15 10 5 0
Y-COORDINATES
0.015 0.010 0.005 0.000 -0.005 -0.010 -0.005 30mA
20mA
0.000 0.005 0.010 X-COORDINATES
0.015
2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VF - FORWARD VOLTAGE - VOLTS Figure 5. Forward Current vs. Forward Voltage
Figure 4. Chromaticity shift vs. Current *Note: (x,y) values @ 20mA reference to (0,0)
4
1
RELATIVE LUMINOUS INTENSITY
Intensity Bin Limit Table Tolerance for each bin limit is 15%
Intensity (mcd) at 20 mA
0.5
Bin N P Q
Min 680 880 1150 1500 1900
Max 880 1150 1500 1900 2500
0 -90
R
-60 -30 0 30 60 90 ANGULAR DISPLACEMENT ()
S
Figure 6. Spatial Radiation Pattern for CW4x
1
RELATIVE LUMINOUS INTENSITY
0.5
0 -90 -60 -30 0 30 60 90 ANGULAR DISPLACEMENT ()
Figure 7. Spatial Radiation Pattern for CW7x
5
Color Bin Limit Table Tolerance for each bin limit is 0.01
Color Bin Limits with Respect to CIE 1931 Chromaticity Diagram
0.40
Rank 1
Limits (Chromaticity Coordinates) X Y 0.330 0.360 0.287 0.295 0.264 0.267 0.283 0.305 0.330 0.318 0.296 0.276 0.280 0.248 0.287 0.295 0.356 0.351 0.330 0.318 0.296 0.276 0.330 0.339 0.361
0.35
2
X Y
0.330 0.339 0.283 0.305 0.330 0.360
Y-COORDINATE
0.385
4 2
1 BLACK BODY CURVE
0.30 3 0.25
3
X Y
4
X Y
0.20 0.26
0.30 0.34 X-COORDINATE
0.38
Note: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. Please contact your Agilent representative for information on currently available bins.
www.agilent.com/ semiconductors
For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright (c) 2004 Agilent Technologies, Inc. October 6, 2004 5989-1453EN

▲Up To Search▲

Price & Availability of HLMP-CW46-QRB00

	To Download HLMP-CW46-QRB00 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .